iio: adc: stm32-adc: smart calibration support
Add smart calibration support for STM32MP1. - STM32MP15x: both linear & offset calibration are supported - STM32MP13x: Only offset calibration is supported Linear calibration: Linear calibration is SoC dependent and does not change over time so it can be done only once. Linear calibration may have already been done in u-boot. Skip calibration execution if calibration data are already available. Save calibration factors in private data and restore them from private data on next ADC start. Offset calibration: This calibration may vary over time, depending on temperature or voltage. Run offset single-ended and differential calibration on each ADC start, as it is not time consuming. This calibration do not need to be saved. So, remove calfact_s and calfact_d value and bitfields that are no longer used. Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com> Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Link: https://lore.kernel.org/r/20221115103124.70074-2-olivier.moysan@foss.st.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit is contained in:
parent
f237cf1914
commit
9d901e356c
@ -142,6 +142,7 @@
|
||||
#define STM32H7_LINCALRDYW3 BIT(24)
|
||||
#define STM32H7_LINCALRDYW2 BIT(23)
|
||||
#define STM32H7_LINCALRDYW1 BIT(22)
|
||||
#define STM32H7_LINCALRDYW_MASK GENMASK(27, 22)
|
||||
#define STM32H7_ADCALLIN BIT(16)
|
||||
#define STM32H7_BOOST BIT(8)
|
||||
#define STM32H7_ADSTP BIT(4)
|
||||
|
@ -119,16 +119,12 @@ struct stm32_adc_trig_info {
|
||||
|
||||
/**
|
||||
* struct stm32_adc_calib - optional adc calibration data
|
||||
* @calfact_s: Calibration offset for single ended channels
|
||||
* @calfact_d: Calibration offset in differential
|
||||
* @lincalfact: Linearity calibration factor
|
||||
* @calibrated: Indicates calibration status
|
||||
* @lincal_saved: Indicates that linear calibration factors are saved
|
||||
*/
|
||||
struct stm32_adc_calib {
|
||||
u32 calfact_s;
|
||||
u32 calfact_d;
|
||||
u32 lincalfact[STM32H7_LINCALFACT_NUM];
|
||||
bool calibrated;
|
||||
bool lincal_saved;
|
||||
};
|
||||
|
||||
/**
|
||||
@ -165,8 +161,6 @@ struct stm32_adc_vrefint {
|
||||
* @extsel: trigger selection register & bitfield
|
||||
* @res: resolution selection register & bitfield
|
||||
* @difsel: differential mode selection register & bitfield
|
||||
* @calfact_s: single-ended calibration factors register & bitfield
|
||||
* @calfact_d: differential calibration factors register & bitfield
|
||||
* @smpr: smpr1 & smpr2 registers offset array
|
||||
* @smp_bits: smpr1 & smpr2 index and bitfields
|
||||
* @or_vddcore: option register & vddcore bitfield
|
||||
@ -186,8 +180,6 @@ struct stm32_adc_regspec {
|
||||
const struct stm32_adc_regs extsel;
|
||||
const struct stm32_adc_regs res;
|
||||
const struct stm32_adc_regs difsel;
|
||||
const struct stm32_adc_regs calfact_s;
|
||||
const struct stm32_adc_regs calfact_d;
|
||||
const u32 smpr[2];
|
||||
const struct stm32_adc_regs *smp_bits;
|
||||
const struct stm32_adc_regs or_vddcore;
|
||||
@ -525,10 +517,6 @@ static const struct stm32_adc_regspec stm32h7_adc_regspec = {
|
||||
STM32H7_EXTSEL_SHIFT },
|
||||
.res = { STM32H7_ADC_CFGR, STM32H7_RES_MASK, STM32H7_RES_SHIFT },
|
||||
.difsel = { STM32H7_ADC_DIFSEL, STM32H7_DIFSEL_MASK},
|
||||
.calfact_s = { STM32H7_ADC_CALFACT, STM32H7_CALFACT_S_MASK,
|
||||
STM32H7_CALFACT_S_SHIFT },
|
||||
.calfact_d = { STM32H7_ADC_CALFACT, STM32H7_CALFACT_D_MASK,
|
||||
STM32H7_CALFACT_D_SHIFT },
|
||||
.smpr = { STM32H7_ADC_SMPR1, STM32H7_ADC_SMPR2 },
|
||||
.smp_bits = stm32h7_smp_bits,
|
||||
};
|
||||
@ -550,10 +538,6 @@ static const struct stm32_adc_regspec stm32mp13_adc_regspec = {
|
||||
STM32H7_EXTSEL_SHIFT },
|
||||
.res = { STM32H7_ADC_CFGR, STM32MP13_RES_MASK, STM32MP13_RES_SHIFT },
|
||||
.difsel = { STM32MP13_ADC_DIFSEL, STM32MP13_DIFSEL_MASK},
|
||||
.calfact_s = { STM32MP13_ADC_CALFACT, STM32MP13_CALFACT_S_MASK,
|
||||
STM32MP13_CALFACT_S_SHIFT },
|
||||
.calfact_d = { STM32MP13_ADC_CALFACT, STM32MP13_CALFACT_D_MASK,
|
||||
STM32MP13_CALFACT_D_SHIFT },
|
||||
.smpr = { STM32H7_ADC_SMPR1, STM32H7_ADC_SMPR2 },
|
||||
.smp_bits = stm32h7_smp_bits,
|
||||
.or_vddcore = { STM32MP13_ADC2_OR, STM32MP13_OP0 },
|
||||
@ -575,10 +559,6 @@ static const struct stm32_adc_regspec stm32mp1_adc_regspec = {
|
||||
STM32H7_EXTSEL_SHIFT },
|
||||
.res = { STM32H7_ADC_CFGR, STM32H7_RES_MASK, STM32H7_RES_SHIFT },
|
||||
.difsel = { STM32H7_ADC_DIFSEL, STM32H7_DIFSEL_MASK},
|
||||
.calfact_s = { STM32H7_ADC_CALFACT, STM32H7_CALFACT_S_MASK,
|
||||
STM32H7_CALFACT_S_SHIFT },
|
||||
.calfact_d = { STM32H7_ADC_CALFACT, STM32H7_CALFACT_D_MASK,
|
||||
STM32H7_CALFACT_D_SHIFT },
|
||||
.smpr = { STM32H7_ADC_SMPR1, STM32H7_ADC_SMPR2 },
|
||||
.smp_bits = stm32h7_smp_bits,
|
||||
.or_vddcore = { STM32MP1_ADC2_OR, STM32MP1_VDDCOREEN },
|
||||
@ -1000,9 +980,6 @@ static int stm32h7_adc_read_selfcalib(struct iio_dev *indio_dev)
|
||||
int i, ret;
|
||||
u32 lincalrdyw_mask, val;
|
||||
|
||||
if (!adc->cfg->has_linearcal)
|
||||
goto skip_linearcal;
|
||||
|
||||
/* Read linearity calibration */
|
||||
lincalrdyw_mask = STM32H7_LINCALRDYW6;
|
||||
for (i = STM32H7_LINCALFACT_NUM - 1; i >= 0; i--) {
|
||||
@ -1024,15 +1001,7 @@ static int stm32h7_adc_read_selfcalib(struct iio_dev *indio_dev)
|
||||
|
||||
lincalrdyw_mask >>= 1;
|
||||
}
|
||||
|
||||
skip_linearcal:
|
||||
/* Read offset calibration */
|
||||
val = stm32_adc_readl(adc, adc->cfg->regs->calfact_s.reg);
|
||||
adc->cal.calfact_s = (val & adc->cfg->regs->calfact_s.mask);
|
||||
adc->cal.calfact_s >>= adc->cfg->regs->calfact_s.shift;
|
||||
adc->cal.calfact_d = (val & adc->cfg->regs->calfact_d.mask);
|
||||
adc->cal.calfact_d >>= adc->cfg->regs->calfact_d.shift;
|
||||
adc->cal.calibrated = true;
|
||||
adc->cal.lincal_saved = true;
|
||||
|
||||
return 0;
|
||||
}
|
||||
@ -1048,13 +1017,6 @@ static int stm32h7_adc_restore_selfcalib(struct iio_dev *indio_dev)
|
||||
int i, ret;
|
||||
u32 lincalrdyw_mask, val;
|
||||
|
||||
val = (adc->cal.calfact_s << adc->cfg->regs->calfact_s.shift) |
|
||||
(adc->cal.calfact_d << adc->cfg->regs->calfact_d.shift);
|
||||
stm32_adc_writel(adc, adc->cfg->regs->calfact_s.reg, val);
|
||||
|
||||
if (!adc->cfg->has_linearcal)
|
||||
return 0;
|
||||
|
||||
lincalrdyw_mask = STM32H7_LINCALRDYW6;
|
||||
for (i = STM32H7_LINCALFACT_NUM - 1; i >= 0; i--) {
|
||||
/*
|
||||
@ -1116,19 +1078,20 @@ static int stm32h7_adc_restore_selfcalib(struct iio_dev *indio_dev)
|
||||
/**
|
||||
* stm32h7_adc_selfcalib() - Procedure to calibrate ADC
|
||||
* @indio_dev: IIO device instance
|
||||
* @do_lincal: linear calibration request flag
|
||||
* Note: Must be called once ADC is out of power down.
|
||||
*
|
||||
* Run offset calibration unconditionally.
|
||||
* Run linear calibration if requested & supported.
|
||||
*/
|
||||
static int stm32h7_adc_selfcalib(struct iio_dev *indio_dev)
|
||||
static int stm32h7_adc_selfcalib(struct iio_dev *indio_dev, int do_lincal)
|
||||
{
|
||||
struct stm32_adc *adc = iio_priv(indio_dev);
|
||||
int ret;
|
||||
u32 msk = STM32H7_ADCALDIF;
|
||||
u32 val;
|
||||
|
||||
if (adc->cal.calibrated)
|
||||
return true;
|
||||
|
||||
if (adc->cfg->has_linearcal)
|
||||
if (adc->cfg->has_linearcal && do_lincal)
|
||||
msk |= STM32H7_ADCALLIN;
|
||||
/* ADC must be disabled for calibration */
|
||||
stm32h7_adc_disable(indio_dev);
|
||||
@ -1172,6 +1135,33 @@ out:
|
||||
return ret;
|
||||
}
|
||||
|
||||
/**
|
||||
* stm32h7_adc_check_selfcalib() - Check linear calibration status
|
||||
* @indio_dev: IIO device instance
|
||||
*
|
||||
* Used to check if linear calibration has been done.
|
||||
* Return true if linear calibration factors are already saved in private data
|
||||
* or if a linear calibration has been done at boot stage.
|
||||
*/
|
||||
static int stm32h7_adc_check_selfcalib(struct iio_dev *indio_dev)
|
||||
{
|
||||
struct stm32_adc *adc = iio_priv(indio_dev);
|
||||
u32 val;
|
||||
|
||||
if (adc->cal.lincal_saved)
|
||||
return true;
|
||||
|
||||
/*
|
||||
* Check if linear calibration factors are available in ADC registers,
|
||||
* by checking that all LINCALRDYWx bits are set.
|
||||
*/
|
||||
val = stm32_adc_readl(adc, STM32H7_ADC_CR) & STM32H7_LINCALRDYW_MASK;
|
||||
if (val == STM32H7_LINCALRDYW_MASK)
|
||||
return true;
|
||||
|
||||
return false;
|
||||
}
|
||||
|
||||
/**
|
||||
* stm32h7_adc_prepare() - Leave power down mode to enable ADC.
|
||||
* @indio_dev: IIO device instance
|
||||
@ -1186,16 +1176,20 @@ out:
|
||||
static int stm32h7_adc_prepare(struct iio_dev *indio_dev)
|
||||
{
|
||||
struct stm32_adc *adc = iio_priv(indio_dev);
|
||||
int calib, ret;
|
||||
int lincal_done = false;
|
||||
int ret;
|
||||
|
||||
ret = stm32h7_adc_exit_pwr_down(indio_dev);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
ret = stm32h7_adc_selfcalib(indio_dev);
|
||||
if (adc->cfg->has_linearcal)
|
||||
lincal_done = stm32h7_adc_check_selfcalib(indio_dev);
|
||||
|
||||
/* Always run offset calibration. Run linear calibration only once */
|
||||
ret = stm32h7_adc_selfcalib(indio_dev, !lincal_done);
|
||||
if (ret < 0)
|
||||
goto pwr_dwn;
|
||||
calib = ret;
|
||||
|
||||
stm32_adc_int_ch_enable(indio_dev);
|
||||
|
||||
@ -1205,13 +1199,15 @@ static int stm32h7_adc_prepare(struct iio_dev *indio_dev)
|
||||
if (ret)
|
||||
goto ch_disable;
|
||||
|
||||
/* Either restore or read calibration result for future reference */
|
||||
if (calib)
|
||||
ret = stm32h7_adc_restore_selfcalib(indio_dev);
|
||||
else
|
||||
ret = stm32h7_adc_read_selfcalib(indio_dev);
|
||||
if (ret)
|
||||
goto disable;
|
||||
if (adc->cfg->has_linearcal) {
|
||||
if (!adc->cal.lincal_saved)
|
||||
ret = stm32h7_adc_read_selfcalib(indio_dev);
|
||||
else
|
||||
ret = stm32h7_adc_restore_selfcalib(indio_dev);
|
||||
|
||||
if (ret)
|
||||
goto disable;
|
||||
}
|
||||
|
||||
if (adc->cfg->has_presel)
|
||||
stm32_adc_writel(adc, STM32H7_ADC_PCSEL, adc->pcsel);
|
||||
|
Loading…
Reference in New Issue
Block a user