linux/Documentation/ABI/testing/sysfs-power

What:		/sys/power/
Date:		August 2006
Contact:	Rafael J. Wysocki <rjw@sisk.pl>
Description:
		The /sys/power directory will contain files that will
		provide a unified interface to the power management
		subsystem.

What:		/sys/power/state
Date:		August 2006
Contact:	Rafael J. Wysocki <rjw@sisk.pl>
Description:
		The /sys/power/state file controls the system power state.
		Reading from this file returns what states are supported,
		which is hard-coded to 'standby' (Power-On Suspend), 'mem'
		(Suspend-to-RAM), and 'disk' (Suspend-to-Disk).

		Writing to this file one of these strings causes the system to
		transition into that state. Please see the file
		Documentation/power/states.txt for a description of each of
		these states.

What:		/sys/power/disk
Date:		September 2006
Contact:	Rafael J. Wysocki <rjw@sisk.pl>
Description:
		The /sys/power/disk file controls the operating mode of the
		suspend-to-disk mechanism.  Reading from this file returns
		the name of the method by which the system will be put to
		sleep on the next suspend.  There are four methods supported:
		'firmware' - means that the memory image will be saved to disk
		by some firmware, in which case we also assume that the
		firmware will handle the system suspend.
		'platform' - the memory image will be saved by the kernel and
		the system will be put to sleep by the platform driver (e.g.
		ACPI or other PM registers).
		'shutdown' - the memory image will be saved by the kernel and
		the system will be powered off.
		'reboot' - the memory image will be saved by the kernel and
		the system will be rebooted.

		Additionally, /sys/power/disk can be used to turn on one of the
		two testing modes of the suspend-to-disk mechanism: 'testproc'
		or 'test'.  If the suspend-to-disk mechanism is in the
		'testproc' mode, writing 'disk' to /sys/power/state will cause
		the kernel to disable nonboot CPUs and freeze tasks, wait for 5
		seconds, unfreeze tasks and enable nonboot CPUs.  If it is in
		the 'test' mode, writing 'disk' to /sys/power/state will cause
		the kernel to disable nonboot CPUs and freeze tasks, shrink
		memory, suspend devices, wait for 5 seconds, resume devices,
		unfreeze tasks and enable nonboot CPUs.  Then, we are able to
		look in the log messages and work out, for example, which code
		is being slow and which device drivers are misbehaving.

		The suspend-to-disk method may be chosen by writing to this
		file one of the accepted strings:

		'firmware'
		'platform'
		'shutdown'
		'reboot'
		'testproc'
		'test'

		It will only change to 'firmware' or 'platform' if the system
		supports that.

What:		/sys/power/image_size
Date:		August 2006
Contact:	Rafael J. Wysocki <rjw@sisk.pl>
Description:
		The /sys/power/image_size file controls the size of the image
		created by the suspend-to-disk mechanism.  It can be written a
		string representing a non-negative integer that will be used
		as an upper limit of the image size, in bytes.  The kernel's
		suspend-to-disk code will do its best to ensure the image size
		will not exceed this number.  However, if it turns out to be
		impossible, the kernel will try to suspend anyway using the
		smallest image possible.  In particular, if "0" is written to
		this file, the suspend image will be as small as possible.

		Reading from this file will display the current image size
		limit, which is set to 500 MB by default.

What:		/sys/power/pm_trace
Date:		August 2006
Contact:	Rafael J. Wysocki <rjw@sisk.pl>
Description:
		The /sys/power/pm_trace file controls the code which saves the
		last PM event point in the RTC across reboots, so that you can
		debug a machine that just hangs during suspend (or more
		commonly, during resume).  Namely, the RTC is only used to save
		the last PM event point if this file contains '1'.  Initially
		it contains '0' which may be changed to '1' by writing a
		string representing a nonzero integer into it.

		To use this debugging feature you should attempt to suspend
		the machine, then reboot it and run

		dmesg -s 1000000 | grep 'hash matches'

		CAUTION: Using it will cause your machine's real-time (CMOS)
		clock to be set to a random invalid time after a resume.