linux/drivers/usb/host/ehci-hub.c

/*
 * Copyright (C) 2001-2004 by David Brownell
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License as published by the
 * Free Software Foundation; either version 2 of the License, or (at your
 * option) any later version.
 *
 * This program is distributed in the hope that it will be useful, but
 * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
 * or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
 * for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software Foundation,
 * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 */

/* this file is part of ehci-hcd.c */

/*-------------------------------------------------------------------------*/

/*
 * EHCI Root Hub ... the nonsharable stuff
 *
 * Registers don't need cpu_to_le32, that happens transparently
 */

/*-------------------------------------------------------------------------*/

#ifdef	CONFIG_PM

static int ehci_hub_control(
	struct usb_hcd	*hcd,
	u16		typeReq,
	u16		wValue,
	u16		wIndex,
	char		*buf,
	u16		wLength
);

/* After a power loss, ports that were owned by the companion must be
 * reset so that the companion can still own them.
 */
static void ehci_handover_companion_ports(struct ehci_hcd *ehci)
{
	u32 __iomem	*reg;
	u32		status;
	int		port;
	__le32		buf;
	struct usb_hcd	*hcd = ehci_to_hcd(ehci);

	if (!ehci->owned_ports)
		return;

	/* Give the connections some time to appear */
	msleep(20);

	port = HCS_N_PORTS(ehci->hcs_params);
	while (port--) {
		if (test_bit(port, &ehci->owned_ports)) {
			reg = &ehci->regs->port_status[port];
			status = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;

			/* Port already owned by companion? */
			if (status & PORT_OWNER)
				clear_bit(port, &ehci->owned_ports);
			else if (test_bit(port, &ehci->companion_ports))
				ehci_writel(ehci, status & ~PORT_PE, reg);
			else
				ehci_hub_control(hcd, SetPortFeature,
						USB_PORT_FEAT_RESET, port + 1,
						NULL, 0);
		}
	}

	if (!ehci->owned_ports)
		return;
	msleep(90);		/* Wait for resets to complete */

	port = HCS_N_PORTS(ehci->hcs_params);
	while (port--) {
		if (test_bit(port, &ehci->owned_ports)) {
			ehci_hub_control(hcd, GetPortStatus,
					0, port + 1,
					(char *) &buf, sizeof(buf));

			/* The companion should now own the port,
			 * but if something went wrong the port must not
			 * remain enabled.
			 */
			reg = &ehci->regs->port_status[port];
			status = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
			if (status & PORT_OWNER)
				ehci_writel(ehci, status | PORT_CSC, reg);
			else {
				ehci_dbg(ehci, "failed handover port %d: %x\n",
						port + 1, status);
				ehci_writel(ehci, status & ~PORT_PE, reg);
			}
		}
	}

	ehci->owned_ports = 0;
}

static int ehci_bus_suspend (struct usb_hcd *hcd)
{
	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
	int			port;
	int			mask;

	ehci_dbg(ehci, "suspend root hub\n");

	if (time_before (jiffies, ehci->next_statechange))
		msleep(5);
	del_timer_sync(&ehci->watchdog);
	del_timer_sync(&ehci->iaa_watchdog);

	port = HCS_N_PORTS (ehci->hcs_params);
	spin_lock_irq (&ehci->lock);

	/* stop schedules, clean any completed work */
	if (HC_IS_RUNNING(hcd->state)) {
		ehci_quiesce (ehci);
		hcd->state = HC_STATE_QUIESCING;
	}
	ehci->command = ehci_readl(ehci, &ehci->regs->command);
	ehci_work(ehci);

	/* Unlike other USB host controller types, EHCI doesn't have
	 * any notion of "global" or bus-wide suspend.  The driver has
	 * to manually suspend all the active unsuspended ports, and
	 * then manually resume them in the bus_resume() routine.
	 */
	ehci->bus_suspended = 0;
	ehci->owned_ports = 0;
	while (port--) {
		u32 __iomem	*reg = &ehci->regs->port_status [port];
		u32		t1 = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
		u32		t2 = t1;

		/* keep track of which ports we suspend */
		if (t1 & PORT_OWNER)
			set_bit(port, &ehci->owned_ports);
		else if ((t1 & PORT_PE) && !(t1 & PORT_SUSPEND)) {
			t2 |= PORT_SUSPEND;
			set_bit(port, &ehci->bus_suspended);
		}

		/* enable remote wakeup on all ports */
		if (device_may_wakeup(&hcd->self.root_hub->dev))
			t2 |= PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E;
		else
			t2 &= ~(PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E);

		if (t1 != t2) {
			ehci_vdbg (ehci, "port %d, %08x -> %08x\n",
				port + 1, t1, t2);
			ehci_writel(ehci, t2, reg);
		}
	}

	/* Apparently some devices need a >= 1-uframe delay here */
	if (ehci->bus_suspended)
		udelay(150);

	/* turn off now-idle HC */
	ehci_halt (ehci);
	hcd->state = HC_STATE_SUSPENDED;

	if (ehci->reclaim)
		end_unlink_async(ehci);

	/* allow remote wakeup */
	mask = INTR_MASK;
	if (!device_may_wakeup(&hcd->self.root_hub->dev))
		mask &= ~STS_PCD;
	ehci_writel(ehci, mask, &ehci->regs->intr_enable);
	ehci_readl(ehci, &ehci->regs->intr_enable);

	ehci->next_statechange = jiffies + msecs_to_jiffies(10);
	spin_unlock_irq (&ehci->lock);
	return 0;
}


/* caller has locked the root hub, and should reset/reinit on error */
static int ehci_bus_resume (struct usb_hcd *hcd)
{
	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
	u32			temp;
	u32			power_okay;
	int			i;

	if (time_before (jiffies, ehci->next_statechange))
		msleep(5);
	spin_lock_irq (&ehci->lock);
	if (!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)) {
		spin_unlock_irq(&ehci->lock);
		return -ESHUTDOWN;
	}

	/* Ideally and we've got a real resume here, and no port's power
	 * was lost.  (For PCI, that means Vaux was maintained.)  But we
	 * could instead be restoring a swsusp snapshot -- so that BIOS was
	 * the last user of the controller, not reset/pm hardware keeping
	 * state we gave to it.
	 */
	power_okay = ehci_readl(ehci, &ehci->regs->intr_enable);
	ehci_dbg(ehci, "resume root hub%s\n",
			power_okay ? "" : " after power loss");

	/* at least some APM implementations will try to deliver
	 * IRQs right away, so delay them until we're ready.
	 */
	ehci_writel(ehci, 0, &ehci->regs->intr_enable);

	/* re-init operational registers */
	ehci_writel(ehci, 0, &ehci->regs->segment);
	ehci_writel(ehci, ehci->periodic_dma, &ehci->regs->frame_list);
	ehci_writel(ehci, (u32) ehci->async->qh_dma, &ehci->regs->async_next);

	/* restore CMD_RUN, framelist size, and irq threshold */
	ehci_writel(ehci, ehci->command, &ehci->regs->command);

	/* Some controller/firmware combinations need a delay during which
	 * they set up the port statuses.  See Bugzilla #8190. */
	mdelay(8);

	/* manually resume the ports we suspended during bus_suspend() */
	i = HCS_N_PORTS (ehci->hcs_params);
	while (i--) {
		temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
		temp &= ~(PORT_RWC_BITS
			| PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E);
		if (test_bit(i, &ehci->bus_suspended) &&
				(temp & PORT_SUSPEND)) {
			ehci->reset_done [i] = jiffies + msecs_to_jiffies (20);
			temp |= PORT_RESUME;
		}
		ehci_writel(ehci, temp, &ehci->regs->port_status [i]);
	}
	i = HCS_N_PORTS (ehci->hcs_params);
	mdelay (20);
	while (i--) {
		temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
		if (test_bit(i, &ehci->bus_suspended) &&
				(temp & PORT_SUSPEND)) {
			temp &= ~(PORT_RWC_BITS | PORT_RESUME);
			ehci_writel(ehci, temp, &ehci->regs->port_status [i]);
			ehci_vdbg (ehci, "resumed port %d\n", i + 1);
		}
	}
	(void) ehci_readl(ehci, &ehci->regs->command);

	/* maybe re-activate the schedule(s) */
	temp = 0;
	if (ehci->async->qh_next.qh)
		temp |= CMD_ASE;
	if (ehci->periodic_sched)
		temp |= CMD_PSE;
	if (temp) {
		ehci->command |= temp;
		ehci_writel(ehci, ehci->command, &ehci->regs->command);
	}

	ehci->next_statechange = jiffies + msecs_to_jiffies(5);
	hcd->state = HC_STATE_RUNNING;

	/* Now we can safely re-enable irqs */
	ehci_writel(ehci, INTR_MASK, &ehci->regs->intr_enable);

	spin_unlock_irq (&ehci->lock);
	ehci_handover_companion_ports(ehci);
	return 0;
}

#else

#define ehci_bus_suspend	NULL
#define ehci_bus_resume		NULL

#endif	/* CONFIG_PM */

/*-------------------------------------------------------------------------*/

/* Display the ports dedicated to the companion controller */
static ssize_t show_companion(struct device *dev,
			      struct device_attribute *attr,
			      char *buf)
{
	struct ehci_hcd		*ehci;
	int			nports, index, n;
	int			count = PAGE_SIZE;
	char			*ptr = buf;

	ehci = hcd_to_ehci(bus_to_hcd(dev_get_drvdata(dev)));
	nports = HCS_N_PORTS(ehci->hcs_params);

	for (index = 0; index < nports; ++index) {
		if (test_bit(index, &ehci->companion_ports)) {
			n = scnprintf(ptr, count, "%d\n", index + 1);
			ptr += n;
			count -= n;
		}
	}
	return ptr - buf;
}

/*
 * Sets the owner of a port
 */
static void set_owner(struct ehci_hcd *ehci, int portnum, int new_owner)
{
	u32 __iomem		*status_reg;
	u32			port_status;
	int 			try;

	status_reg = &ehci->regs->port_status[portnum];

	/*
	 * The controller won't set the OWNER bit if the port is
	 * enabled, so this loop will sometimes require at least two
	 * iterations: one to disable the port and one to set OWNER.
	 */
	for (try = 4; try > 0; --try) {
		spin_lock_irq(&ehci->lock);
		port_status = ehci_readl(ehci, status_reg);
		if ((port_status & PORT_OWNER) == new_owner
				|| (port_status & (PORT_OWNER | PORT_CONNECT))
					== 0)
			try = 0;
		else {
			port_status ^= PORT_OWNER;
			port_status &= ~(PORT_PE | PORT_RWC_BITS);
			ehci_writel(ehci, port_status, status_reg);
		}
		spin_unlock_irq(&ehci->lock);
		if (try > 1)
			msleep(5);
	}
}

/*
 * Dedicate or undedicate a port to the companion controller.
 * Syntax is "[-]portnum", where a leading '-' sign means
 * return control of the port to the EHCI controller.
 */
static ssize_t store_companion(struct device *dev,
			       struct device_attribute *attr,
			       const char *buf, size_t count)
{
	struct ehci_hcd		*ehci;
	int			portnum, new_owner;

	ehci = hcd_to_ehci(bus_to_hcd(dev_get_drvdata(dev)));
	new_owner = PORT_OWNER;		/* Owned by companion */
	if (sscanf(buf, "%d", &portnum) != 1)
		return -EINVAL;
	if (portnum < 0) {
		portnum = - portnum;
		new_owner = 0;		/* Owned by EHCI */
	}
	if (portnum <= 0 || portnum > HCS_N_PORTS(ehci->hcs_params))
		return -ENOENT;
	portnum--;
	if (new_owner)
		set_bit(portnum, &ehci->companion_ports);
	else
		clear_bit(portnum, &ehci->companion_ports);
	set_owner(ehci, portnum, new_owner);
	return count;
}
static DEVICE_ATTR(companion, 0644, show_companion, store_companion);

static inline void create_companion_file(struct ehci_hcd *ehci)
{
	int	i;

	/* with integrated TT there is no companion! */
	if (!ehci_is_TDI(ehci))
		i = device_create_file(ehci_to_hcd(ehci)->self.dev,
				       &dev_attr_companion);
}

static inline void remove_companion_file(struct ehci_hcd *ehci)
{
	/* with integrated TT there is no companion! */
	if (!ehci_is_TDI(ehci))
		device_remove_file(ehci_to_hcd(ehci)->self.dev,
				   &dev_attr_companion);
}


/*-------------------------------------------------------------------------*/

static int check_reset_complete (
	struct ehci_hcd	*ehci,
	int		index,
	u32 __iomem	*status_reg,
	int		port_status
) {
	if (!(port_status & PORT_CONNECT))
		return port_status;

	/* if reset finished and it's still not enabled -- handoff */
	if (!(port_status & PORT_PE)) {

		/* with integrated TT, there's nobody to hand it to! */
		if (ehci_is_TDI(ehci)) {
			ehci_dbg (ehci,
				"Failed to enable port %d on root hub TT\n",
				index+1);
			return port_status;
		}

		ehci_dbg (ehci, "port %d full speed --> companion\n",
			index + 1);

		// what happens if HCS_N_CC(params) == 0 ?
		port_status |= PORT_OWNER;
		port_status &= ~PORT_RWC_BITS;
		ehci_writel(ehci, port_status, status_reg);

	} else
		ehci_dbg (ehci, "port %d high speed\n", index + 1);

	return port_status;
}

/*-------------------------------------------------------------------------*/


/* build "status change" packet (one or two bytes) from HC registers */

static int
ehci_hub_status_data (struct usb_hcd *hcd, char *buf)
{
	struct ehci_hcd	*ehci = hcd_to_ehci (hcd);
	u32		temp, status = 0;
	u32		mask;
	int		ports, i, retval = 1;
	unsigned long	flags;

	/* if !USB_SUSPEND, root hub timers won't get shut down ... */
	if (!HC_IS_RUNNING(hcd->state))
		return 0;

	/* init status to no-changes */
	buf [0] = 0;
	ports = HCS_N_PORTS (ehci->hcs_params);
	if (ports > 7) {
		buf [1] = 0;
		retval++;
	}

	/* Some boards (mostly VIA?) report bogus overcurrent indications,
	 * causing massive log spam unless we completely ignore them.  It
	 * may be relevant that VIA VT8235 controllers, where PORT_POWER is
	 * always set, seem to clear PORT_OCC and PORT_CSC when writing to
	 * PORT_POWER; that's surprising, but maybe within-spec.
	 */
	if (!ignore_oc)
		mask = PORT_CSC | PORT_PEC | PORT_OCC;
	else
		mask = PORT_CSC | PORT_PEC;
	// PORT_RESUME from hardware ~= PORT_STAT_C_SUSPEND

	/* no hub change reports (bit 0) for now (power, ...) */

	/* port N changes (bit N)? */
	spin_lock_irqsave (&ehci->lock, flags);
	for (i = 0; i < ports; i++) {
		temp = ehci_readl(ehci, &ehci->regs->port_status [i]);

		/*
		 * Return status information even for ports with OWNER set.
		 * Otherwise khubd wouldn't see the disconnect event when a
		 * high-speed device is switched over to the companion
		 * controller by the user.
		 */

		if ((temp & mask) != 0
				|| ((temp & PORT_RESUME) != 0
					&& time_after_eq(jiffies,
						ehci->reset_done[i]))) {
			if (i < 7)
			    buf [0] |= 1 << (i + 1);
			else
			    buf [1] |= 1 << (i - 7);
			status = STS_PCD;
		}
	}
	/* FIXME autosuspend idle root hubs */
	spin_unlock_irqrestore (&ehci->lock, flags);
	return status ? retval : 0;
}

/*-------------------------------------------------------------------------*/

static void
ehci_hub_descriptor (
	struct ehci_hcd			*ehci,
	struct usb_hub_descriptor	*desc
) {
	int		ports = HCS_N_PORTS (ehci->hcs_params);
	u16		temp;

	desc->bDescriptorType = 0x29;
	desc->bPwrOn2PwrGood = 10;	/* ehci 1.0, 2.3.9 says 20ms max */
	desc->bHubContrCurrent = 0;

	desc->bNbrPorts = ports;
	temp = 1 + (ports / 8);
	desc->bDescLength = 7 + 2 * temp;

	/* two bitmaps:  ports removable, and usb 1.0 legacy PortPwrCtrlMask */
	memset (&desc->bitmap [0], 0, temp);
	memset (&desc->bitmap [temp], 0xff, temp);

	temp = 0x0008;			/* per-port overcurrent reporting */
	if (HCS_PPC (ehci->hcs_params))
		temp |= 0x0001;		/* per-port power control */
	else
		temp |= 0x0002;		/* no power switching */
#if 0
// re-enable when we support USB_PORT_FEAT_INDICATOR below.
	if (HCS_INDICATOR (ehci->hcs_params))
		temp |= 0x0080;		/* per-port indicators (LEDs) */
#endif
	desc->wHubCharacteristics = (__force __u16)cpu_to_le16 (temp);
}

/*-------------------------------------------------------------------------*/

#define	PORT_WAKE_BITS	(PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E)

static int ehci_hub_control (
	struct usb_hcd	*hcd,
	u16		typeReq,
	u16		wValue,
	u16		wIndex,
	char		*buf,
	u16		wLength
) {
	struct ehci_hcd	*ehci = hcd_to_ehci (hcd);
	int		ports = HCS_N_PORTS (ehci->hcs_params);
	u32 __iomem	*status_reg = &ehci->regs->port_status[
				(wIndex & 0xff) - 1];
	u32		temp, status;
	unsigned long	flags;
	int		retval = 0;
	unsigned	selector;

	/*
	 * FIXME:  support SetPortFeatures USB_PORT_FEAT_INDICATOR.
	 * HCS_INDICATOR may say we can change LEDs to off/amber/green.
	 * (track current state ourselves) ... blink for diagnostics,
	 * power, "this is the one", etc.  EHCI spec supports this.
	 */

	spin_lock_irqsave (&ehci->lock, flags);
	switch (typeReq) {
	case ClearHubFeature:
		switch (wValue) {
		case C_HUB_LOCAL_POWER:
		case C_HUB_OVER_CURRENT:
			/* no hub-wide feature/status flags */
			break;
		default:
			goto error;
		}
		break;
	case ClearPortFeature:
		if (!wIndex || wIndex > ports)
			goto error;
		wIndex--;
		temp = ehci_readl(ehci, status_reg);

		/*
		 * Even if OWNER is set, so the port is owned by the
		 * companion controller, khubd needs to be able to clear
		 * the port-change status bits (especially
		 * USB_PORT_FEAT_C_CONNECTION).
		 */

		switch (wValue) {
		case USB_PORT_FEAT_ENABLE:
			ehci_writel(ehci, temp & ~PORT_PE, status_reg);
			break;
		case USB_PORT_FEAT_C_ENABLE:
			ehci_writel(ehci, (temp & ~PORT_RWC_BITS) | PORT_PEC,
					status_reg);
			break;
		case USB_PORT_FEAT_SUSPEND:
			if (temp & PORT_RESET)
				goto error;
			if (ehci->no_selective_suspend)
				break;
			if (temp & PORT_SUSPEND) {
				if ((temp & PORT_PE) == 0)
					goto error;
				/* resume signaling for 20 msec */
				temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
				ehci_writel(ehci, temp | PORT_RESUME,
						status_reg);
				ehci->reset_done [wIndex] = jiffies
						+ msecs_to_jiffies (20);
			}
			break;
		case USB_PORT_FEAT_C_SUSPEND:
			/* we auto-clear this feature */
			break;
		case USB_PORT_FEAT_POWER:
			if (HCS_PPC (ehci->hcs_params))
				ehci_writel(ehci,
					  temp & ~(PORT_RWC_BITS | PORT_POWER),
					  status_reg);
			break;
		case USB_PORT_FEAT_C_CONNECTION:
			ehci_writel(ehci, (temp & ~PORT_RWC_BITS) | PORT_CSC,
					status_reg);
			break;
		case USB_PORT_FEAT_C_OVER_CURRENT:
			ehci_writel(ehci, (temp & ~PORT_RWC_BITS) | PORT_OCC,
					status_reg);
			break;
		case USB_PORT_FEAT_C_RESET:
			/* GetPortStatus clears reset */
			break;
		default:
			goto error;
		}
		ehci_readl(ehci, &ehci->regs->command);	/* unblock posted write */
		break;
	case GetHubDescriptor:
		ehci_hub_descriptor (ehci, (struct usb_hub_descriptor *)
			buf);
		break;
	case GetHubStatus:
		/* no hub-wide feature/status flags */
		memset (buf, 0, 4);
		//cpu_to_le32s ((u32 *) buf);
		break;
	case GetPortStatus:
		if (!wIndex || wIndex > ports)
			goto error;
		wIndex--;
		status = 0;
		temp = ehci_readl(ehci, status_reg);

		// wPortChange bits
		if (temp & PORT_CSC)
			status |= 1 << USB_PORT_FEAT_C_CONNECTION;
		if (temp & PORT_PEC)
			status |= 1 << USB_PORT_FEAT_C_ENABLE;

		if ((temp & PORT_OCC) && !ignore_oc){
			status |= 1 << USB_PORT_FEAT_C_OVER_CURRENT;

			/*
			 * Hubs should disable port power on over-current.
			 * However, not all EHCI implementations do this
			 * automatically, even if they _do_ support per-port
			 * power switching; they're allowed to just limit the
			 * current.  khubd will turn the power back on.
			 */
			if (HCS_PPC (ehci->hcs_params)){
				ehci_writel(ehci,
					temp & ~(PORT_RWC_BITS | PORT_POWER),
					status_reg);
			}
		}

		/* whoever resumes must GetPortStatus to complete it!! */
		if (temp & PORT_RESUME) {

			/* Remote Wakeup received? */
			if (!ehci->reset_done[wIndex]) {
				/* resume signaling for 20 msec */
				ehci->reset_done[wIndex] = jiffies
						+ msecs_to_jiffies(20);
				/* check the port again */
				mod_timer(&ehci_to_hcd(ehci)->rh_timer,
						ehci->reset_done[wIndex]);
			}

			/* resume completed? */
			else if (time_after_eq(jiffies,
					ehci->reset_done[wIndex])) {
				status |= 1 << USB_PORT_FEAT_C_SUSPEND;
				ehci->reset_done[wIndex] = 0;

				/* stop resume signaling */
				temp = ehci_readl(ehci, status_reg);
				ehci_writel(ehci,
					temp & ~(PORT_RWC_BITS | PORT_RESUME),
					status_reg);
				retval = handshake(ehci, status_reg,
					   PORT_RESUME, 0, 2000 /* 2msec */);
				if (retval != 0) {
					ehci_err(ehci,
						"port %d resume error %d\n",
						wIndex + 1, retval);
					goto error;
				}
				temp &= ~(PORT_SUSPEND|PORT_RESUME|(3<<10));
			}
		}

		/* whoever resets must GetPortStatus to complete it!! */
		if ((temp & PORT_RESET)
				&& time_after_eq(jiffies,
					ehci->reset_done[wIndex])) {
			status |= 1 << USB_PORT_FEAT_C_RESET;
			ehci->reset_done [wIndex] = 0;

			/* force reset to complete */
			ehci_writel(ehci, temp & ~(PORT_RWC_BITS | PORT_RESET),
					status_reg);
			/* REVISIT:  some hardware needs 550+ usec to clear
			 * this bit; seems too long to spin routinely...
			 */
			retval = handshake(ehci, status_reg,
					PORT_RESET, 0, 750);
			if (retval != 0) {
				ehci_err (ehci, "port %d reset error %d\n",
					wIndex + 1, retval);
				goto error;
			}

			/* see what we found out */
			temp = check_reset_complete (ehci, wIndex, status_reg,
					ehci_readl(ehci, status_reg));
		}

		/* transfer dedicated ports to the companion hc */
		if ((temp & PORT_CONNECT) &&
				test_bit(wIndex, &ehci->companion_ports)) {
			temp &= ~PORT_RWC_BITS;
			temp |= PORT_OWNER;
			ehci_writel(ehci, temp, status_reg);
			ehci_dbg(ehci, "port %d --> companion\n", wIndex + 1);
			temp = ehci_readl(ehci, status_reg);
		}

		/*
		 * Even if OWNER is set, there's no harm letting khubd
		 * see the wPortStatus values (they should all be 0 except
		 * for PORT_POWER anyway).
		 */

		if (temp & PORT_CONNECT) {
			status |= 1 << USB_PORT_FEAT_CONNECTION;
			// status may be from integrated TT
			status |= ehci_port_speed(ehci, temp);
		}
		if (temp & PORT_PE)
			status |= 1 << USB_PORT_FEAT_ENABLE;
		if (temp & (PORT_SUSPEND|PORT_RESUME))
			status |= 1 << USB_PORT_FEAT_SUSPEND;
		if (temp & PORT_OC)
			status |= 1 << USB_PORT_FEAT_OVER_CURRENT;
		if (temp & PORT_RESET)
			status |= 1 << USB_PORT_FEAT_RESET;
		if (temp & PORT_POWER)
			status |= 1 << USB_PORT_FEAT_POWER;

#ifndef	VERBOSE_DEBUG
	if (status & ~0xffff)	/* only if wPortChange is interesting */
#endif
		dbg_port (ehci, "GetStatus", wIndex + 1, temp);
		put_unaligned(cpu_to_le32 (status), (__le32 *) buf);
		break;
	case SetHubFeature:
		switch (wValue) {
		case C_HUB_LOCAL_POWER:
		case C_HUB_OVER_CURRENT:
			/* no hub-wide feature/status flags */
			break;
		default:
			goto error;
		}
		break;
	case SetPortFeature:
		selector = wIndex >> 8;
		wIndex &= 0xff;
		if (!wIndex || wIndex > ports)
			goto error;
		wIndex--;
		temp = ehci_readl(ehci, status_reg);
		if (temp & PORT_OWNER)
			break;

		temp &= ~PORT_RWC_BITS;
		switch (wValue) {
		case USB_PORT_FEAT_SUSPEND:
			if (ehci->no_selective_suspend)
				break;
			if ((temp & PORT_PE) == 0
					|| (temp & PORT_RESET) != 0)
				goto error;
			if (device_may_wakeup(&hcd->self.root_hub->dev))
				temp |= PORT_WAKE_BITS;
			ehci_writel(ehci, temp | PORT_SUSPEND, status_reg);
			break;
		case USB_PORT_FEAT_POWER:
			if (HCS_PPC (ehci->hcs_params))
				ehci_writel(ehci, temp | PORT_POWER,
						status_reg);
			break;
		case USB_PORT_FEAT_RESET:
			if (temp & PORT_RESUME)
				goto error;
			/* line status bits may report this as low speed,
			 * which can be fine if this root hub has a
			 * transaction translator built in.
			 */
			if ((temp & (PORT_PE|PORT_CONNECT)) == PORT_CONNECT
					&& !ehci_is_TDI(ehci)
					&& PORT_USB11 (temp)) {
				ehci_dbg (ehci,
					"port %d low speed --> companion\n",
					wIndex + 1);
				temp |= PORT_OWNER;
			} else {
				ehci_vdbg (ehci, "port %d reset\n", wIndex + 1);
				temp |= PORT_RESET;
				temp &= ~PORT_PE;

				/*
				 * caller must wait, then call GetPortStatus
				 * usb 2.0 spec says 50 ms resets on root
				 */
				ehci->reset_done [wIndex] = jiffies
						+ msecs_to_jiffies (50);
			}
			ehci_writel(ehci, temp, status_reg);
			break;

		/* For downstream facing ports (these):  one hub port is put
		 * into test mode according to USB2 11.24.2.13, then the hub
		 * must be reset (which for root hub now means rmmod+modprobe,
		 * or else system reboot).  See EHCI 2.3.9 and 4.14 for info
		 * about the EHCI-specific stuff.
		 */
		case USB_PORT_FEAT_TEST:
			if (!selector || selector > 5)
				goto error;
			ehci_quiesce(ehci);
			ehci_halt(ehci);
			temp |= selector << 16;
			ehci_writel(ehci, temp, status_reg);
			break;

		default:
			goto error;
		}
		ehci_readl(ehci, &ehci->regs->command);	/* unblock posted writes */
		break;

	default:
error:
		/* "stall" on error */
		retval = -EPIPE;
	}
	spin_unlock_irqrestore (&ehci->lock, flags);
	return retval;
}

static void ehci_relinquish_port(struct usb_hcd *hcd, int portnum)
{
	struct ehci_hcd		*ehci = hcd_to_ehci(hcd);

	if (ehci_is_TDI(ehci))
		return;
	set_owner(ehci, --portnum, PORT_OWNER);
}