linux/arch/arm/mach-omap2/omap_phy_internal.c

/*
  * This file configures the internal USB PHY in OMAP4430. Used
  * with TWL6030 transceiver and MUSB on OMAP4430.
  *
  * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation; either version 2 of the License, or
  * (at your option) any later version.
  *
  * Author: Hema HK <hemahk@ti.com>
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  *
  */

#include <linux/types.h>
#include <linux/delay.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/err.h>
#include <linux/usb.h>

#include <plat/usb.h>
#include "control.h"

/* OMAP control module register for UTMI PHY */
#define CONTROL_DEV_CONF		0x300
#define PHY_PD				0x1

#define USBOTGHS_CONTROL		0x33c
#define	AVALID				BIT(0)
#define	BVALID				BIT(1)
#define	VBUSVALID			BIT(2)
#define	SESSEND				BIT(3)
#define	IDDIG				BIT(4)

static struct clk *phyclk, *clk48m, *clk32k;
static void __iomem *ctrl_base;

int omap4430_phy_init(struct device *dev)
{
	ctrl_base = ioremap(OMAP443X_SCM_BASE, SZ_1K);
	if (!ctrl_base) {
		dev_err(dev, "control module ioremap failed\n");
		return -ENOMEM;
	}
	/* Power down the phy */
	__raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF);
	phyclk = clk_get(dev, "ocp2scp_usb_phy_ick");

	if (IS_ERR(phyclk)) {
		dev_err(dev, "cannot clk_get ocp2scp_usb_phy_ick\n");
		iounmap(ctrl_base);
		return PTR_ERR(phyclk);
	}

	clk48m = clk_get(dev, "ocp2scp_usb_phy_phy_48m");
	if (IS_ERR(clk48m)) {
		dev_err(dev, "cannot clk_get ocp2scp_usb_phy_phy_48m\n");
		clk_put(phyclk);
		iounmap(ctrl_base);
		return PTR_ERR(clk48m);
	}

	clk32k = clk_get(dev, "usb_phy_cm_clk32k");
	if (IS_ERR(clk32k)) {
		dev_err(dev, "cannot clk_get usb_phy_cm_clk32k\n");
		clk_put(phyclk);
		clk_put(clk48m);
		iounmap(ctrl_base);
		return PTR_ERR(clk32k);
	}
	return 0;
}

int omap4430_phy_set_clk(struct device *dev, int on)
{
	static int state;

	if (on && !state) {
		/* Enable the phy clocks */
		clk_enable(phyclk);
		clk_enable(clk48m);
		clk_enable(clk32k);
		state = 1;
	} else if (state) {
		/* Disable the phy clocks */
		clk_disable(phyclk);
		clk_disable(clk48m);
		clk_disable(clk32k);
		state = 0;
	}
	return 0;
}

int omap4430_phy_power(struct device *dev, int ID, int on)
{
	if (on) {
		/* enabled the clocks */
		omap4430_phy_set_clk(dev, 1);
		/* power on the phy */
		if (__raw_readl(ctrl_base + CONTROL_DEV_CONF) & PHY_PD) {
			__raw_writel(~PHY_PD, ctrl_base + CONTROL_DEV_CONF);
			mdelay(200);
		}
		if (ID)
			/* enable VBUS valid, IDDIG groung */
			__raw_writel(AVALID | VBUSVALID, ctrl_base +
							USBOTGHS_CONTROL);
		else
			/*
			 * Enable VBUS Valid, AValid and IDDIG
			 * high impedence
			 */
			__raw_writel(IDDIG | AVALID | VBUSVALID,
						ctrl_base + USBOTGHS_CONTROL);
	} else {
		/* Enable session END and IDIG to high impedence. */
		__raw_writel(SESSEND | IDDIG, ctrl_base +
					USBOTGHS_CONTROL);
		/* Disable the clocks */
		omap4430_phy_set_clk(dev, 0);
		/* Power down the phy */
		__raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF);
	}

	return 0;
}

int omap4430_phy_exit(struct device *dev)
{
	if (ctrl_base)
		iounmap(ctrl_base);
	if (phyclk)
		clk_put(phyclk);
	if (clk48m)
		clk_put(clk48m);
	if (clk32k)
		clk_put(clk32k);

	return 0;
}

void am35x_musb_reset(void)
{
	u32	regval;

	/* Reset the musb interface */
	regval = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET);

	regval |= AM35XX_USBOTGSS_SW_RST;
	omap_ctrl_writel(regval, AM35XX_CONTROL_IP_SW_RESET);

	regval &= ~AM35XX_USBOTGSS_SW_RST;
	omap_ctrl_writel(regval, AM35XX_CONTROL_IP_SW_RESET);

	regval = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET);
}

void am35x_musb_phy_power(u8 on)
{
	unsigned long timeout = jiffies + msecs_to_jiffies(100);
	u32 devconf2;

	if (on) {
		/*
		 * Start the on-chip PHY and its PLL.
		 */
		devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);

		devconf2 &= ~(CONF2_RESET | CONF2_PHYPWRDN | CONF2_OTGPWRDN);
		devconf2 |= CONF2_PHY_PLLON;

		omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);

		pr_info(KERN_INFO "Waiting for PHY clock good...\n");
		while (!(omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2)
				& CONF2_PHYCLKGD)) {
			cpu_relax();

			if (time_after(jiffies, timeout)) {
				pr_err(KERN_ERR "musb PHY clock good timed out\n");
				break;
			}
		}
	} else {
		/*
		 * Power down the on-chip PHY.
		 */
		devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);

		devconf2 &= ~CONF2_PHY_PLLON;
		devconf2 |=  CONF2_PHYPWRDN | CONF2_OTGPWRDN;
		omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
	}
}

void am35x_musb_clear_irq(void)
{
	u32 regval;

	regval = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
	regval |= AM35XX_USBOTGSS_INT_CLR;
	omap_ctrl_writel(regval, AM35XX_CONTROL_LVL_INTR_CLEAR);
	regval = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
}

void am35x_musb_set_mode(u8 musb_mode)
{
	u32 devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);

	devconf2 &= ~CONF2_OTGMODE;
	switch (musb_mode) {
#ifdef	CONFIG_USB_MUSB_HDRC_HCD
	case MUSB_HOST:		/* Force VBUS valid, ID = 0 */
		devconf2 |= CONF2_FORCE_HOST;
		break;
#endif
#ifdef	CONFIG_USB_GADGET_MUSB_HDRC
	case MUSB_PERIPHERAL:	/* Force VBUS valid, ID = 1 */
		devconf2 |= CONF2_FORCE_DEVICE;
		break;
#endif
#ifdef	CONFIG_USB_MUSB_OTG
	case MUSB_OTG:		/* Don't override the VBUS/ID comparators */
		devconf2 |= CONF2_NO_OVERRIDE;
		break;
#endif
	default:
		pr_info(KERN_INFO "Unsupported mode %u\n", musb_mode);
	}

	omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
}