linux/Documentation/networking/dsa/b53.rst

.. SPDX-License-Identifier: GPL-2.0

==========================================
Broadcom RoboSwitch Ethernet switch driver
==========================================

The Broadcom RoboSwitch Ethernet switch family is used in quite a range of
xDSL router, cable modems and other multimedia devices.

The actual implementation supports the devices BCM5325E, BCM5365, BCM539x,
BCM53115 and BCM53125 as well as BCM63XX.

Implementation details
======================

The driver is located in ``drivers/net/dsa/b53/`` and is implemented as a
DSA driver; see ``Documentation/networking/dsa/dsa.rst`` for details on the
subsystem and what it provides.

The switch is, if possible, configured to enable a Broadcom specific 4-bytes
switch tag which gets inserted by the switch for every packet forwarded to the
CPU interface, conversely, the CPU network interface should insert a similar
tag for packets entering the CPU port. The tag format is described in
``net/dsa/tag_brcm.c``.

The configuration of the device depends on whether or not tagging is
supported.

The interface names and example network configuration are used according the
configuration described in the :ref:`dsa-config-showcases`.

Configuration with tagging support
----------------------------------

The tagging based configuration is desired. It is not specific to the b53
DSA driver and will work like all DSA drivers which supports tagging.

See :ref:`dsa-tagged-configuration`.

Configuration without tagging support
-------------------------------------

Older models (5325, 5365) support a different tag format that is not supported
yet. 539x and 531x5 require managed mode and some special handling, which is
also not yet supported. The tagging support is disabled in these cases and the
switch need a different configuration.

The configuration slightly differ from the :ref:`dsa-vlan-configuration`.

The b53 tags the CPU port in all VLANs, since otherwise any PVID untagged
VLAN programming would basically change the CPU port's default PVID and make
it untagged, undesirable.

In difference to the configuration described in :ref:`dsa-vlan-configuration`
the default VLAN 1 has to be removed from the user interface configuration in
single port and gateway configuration, while there is no need to add an extra
VLAN configuration in the bridge showcase.

single port
~~~~~~~~~~~
The configuration can only be set up via VLAN tagging and bridge setup.
By default packages are tagged with vid 1:

.. code-block:: sh

  # tag traffic on CPU port
  ip link add link eth0 name eth0.1 type vlan id 1
  ip link add link eth0 name eth0.2 type vlan id 2
  ip link add link eth0 name eth0.3 type vlan id 3

  # The conduit interface needs to be brought up before the user ports.
  ip link set eth0 up
  ip link set eth0.1 up
  ip link set eth0.2 up
  ip link set eth0.3 up

  # bring up the user interfaces
  ip link set wan up
  ip link set lan1 up
  ip link set lan2 up

  # create bridge
  ip link add name br0 type bridge

  # activate VLAN filtering
  ip link set dev br0 type bridge vlan_filtering 1

  # add ports to bridges
  ip link set dev wan master br0
  ip link set dev lan1 master br0
  ip link set dev lan2 master br0

  # tag traffic on ports
  bridge vlan add dev lan1 vid 2 pvid untagged
  bridge vlan del dev lan1 vid 1
  bridge vlan add dev lan2 vid 3 pvid untagged
  bridge vlan del dev lan2 vid 1

  # configure the VLANs
  ip addr add 192.0.2.1/30 dev eth0.1
  ip addr add 192.0.2.5/30 dev eth0.2
  ip addr add 192.0.2.9/30 dev eth0.3

  # bring up the bridge devices
  ip link set br0 up


bridge
~~~~~~

.. code-block:: sh

  # tag traffic on CPU port
  ip link add link eth0 name eth0.1 type vlan id 1

  # The conduit interface needs to be brought up before the user ports.
  ip link set eth0 up
  ip link set eth0.1 up

  # bring up the user interfaces
  ip link set wan up
  ip link set lan1 up
  ip link set lan2 up

  # create bridge
  ip link add name br0 type bridge

  # activate VLAN filtering
  ip link set dev br0 type bridge vlan_filtering 1

  # add ports to bridge
  ip link set dev wan master br0
  ip link set dev lan1 master br0
  ip link set dev lan2 master br0
  ip link set eth0.1 master br0

  # configure the bridge
  ip addr add 192.0.2.129/25 dev br0

  # bring up the bridge
  ip link set dev br0 up

gateway
~~~~~~~

.. code-block:: sh

  # tag traffic on CPU port
  ip link add link eth0 name eth0.1 type vlan id 1
  ip link add link eth0 name eth0.2 type vlan id 2

  # The conduit interface needs to be brought up before the user ports.
  ip link set eth0 up
  ip link set eth0.1 up
  ip link set eth0.2 up

  # bring up the user interfaces
  ip link set wan up
  ip link set lan1 up
  ip link set lan2 up

  # create bridge
  ip link add name br0 type bridge

  # activate VLAN filtering
  ip link set dev br0 type bridge vlan_filtering 1

  # add ports to bridges
  ip link set dev wan master br0
  ip link set eth0.1 master br0
  ip link set dev lan1 master br0
  ip link set dev lan2 master br0

  # tag traffic on ports
  bridge vlan add dev wan vid 2 pvid untagged
  bridge vlan del dev wan vid 1

  # configure the VLANs
  ip addr add 192.0.2.1/30 dev eth0.2
  ip addr add 192.0.2.129/25 dev br0

  # bring up the bridge devices
  ip link set br0 up