kevin/linux
1
Fork 0
Code
3fa5b8e082
linux/drivers/regulator/Makefile

27 lines
966 B
Makefile
Raw Normal View History

regulator: core kbuild files This patch adds kernel build support for the regulator core. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
2008-04-30 09:13:42 -07:00
#
# Makefile for regulator drivers.
#
obj-$(CONFIG_REGULATOR) += core.o
obj-$(CONFIG_REGULATOR_FIXED_VOLTAGE) += fixed.o
obj-$(CONFIG_REGULATOR_VIRTUAL_CONSUMER) += virtual.o
regulator: add userspace-consumer driver The userspace-consumer driver allows control of voltage and current regulator state from userspace. This is required for fine-grained power management of devices that are completely controller by userspace applications, e.g. a GPS transciever connected to a serial port. Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-04-26 06:49:39 -07:00
obj-$(CONFIG_REGULATOR_USERSPACE_CONSUMER) += userspace-consumer.o
regulator: core kbuild files This patch adds kernel build support for the regulator core. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
2008-04-30 09:13:42 -07:00
regulator: TI bq24022 Li-Ion Charger driver This adds a regulator driver for the TI bq24022 Single-Chip Li-Ion Charger with its nCE and ISET2 pins connected to GPIOs. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
2008-07-11 08:28:06 -07:00
obj-$(CONFIG_REGULATOR_BQ24022) += bq24022.o
LP3971 PMIC regulator driver (updated and combined version) This patch adds regulator drivers for National Semiconductors LP3971 PMIC. This LP3971 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out (LDO) regulators. LP3971 PMIC controller uses I2C interface. Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-05-18 22:33:55 -07:00
obj-$(CONFIG_REGULATOR_LP3971) += lp3971.o
Maxim 1586 regulator driver The Maxim 1586 regulator is a voltage regulator with 2 voltage outputs, specially suitable for Marvell PXA chips. One output is in the range of required VCC_CORE by the PXA27x chips, the other in the VCC_USIM required as well by PXA27x chips. The chip is controlled through the I2C bus. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-04-23 11:10:43 -07:00
obj-$(CONFIG_REGULATOR_MAX1586) += max1586.o
regulator: twl4030 regulators Support most of the LDO regulators in the twl4030 family chips. In the case of LDOs supporting MMC/SD, the voltage controls are used; but in most other cases, the regulator framework is only used to enable/disable a supplies, conserving power when a given voltage rail is not needed. The drivers/mfd/twl4030-core.c code already sets up the various regulators according to board-specific configuration, and knows that some chips don't provide the full set of voltage rails. The omitted regulators are intended to be under hardware control, such as during the hardware-mediated system powerup, powerdown, and suspend states. Unless/until software hooks are known to be safe, they won't be exported here. These regulators implement the new get_status() operation, but can't realistically implement get_mode(); the status output is effectively the result of a vote, with the relevant hardware inputs not exposed. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-02-08 11:37:06 -07:00
obj-$(CONFIG_REGULATOR_TWL4030) += twl4030-regulator.o
regulator: Add WM831x DC-DC buck convertor support The WM831x series of devices all have 3 DC-DC buck convertors. This driver implements software control for these regulators via the regulator API. Use with split hardware/software control of individual regulators is not supported, though regulators not controlled by software may be controlled via the hardware control interfaces. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-07-28 07:21:49 -07:00
obj-$(CONFIG_REGULATOR_WM831X) += wm831x-dcdc.o
regulator: Add WM831x ISINK support The WM831x series of PMICs provide two constant current sinks designed to drive strings of serially connected LEDs for applications such as backlights. This driver adds support for those regulators. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-07-28 07:23:46 -07:00
obj-$(CONFIG_REGULATOR_WM831X) += wm831x-isink.o
regulator: Add WM831x LDO support The WM831x series of devices provide three types of LDO: - General purpose LDOs supporting voltages from 0.9-3.3V - High performance analogue LDOs supporting voltages from 1-3.5V - Very low power consumption LDOs intended to support always on functionality. This patch adds support for all three kinds of LDO. Each regulator is probed as an individual platform device with resources used to provide the register map location of the regulator. Mixed hardware and software control of regulators is not current supported. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-07-28 07:22:02 -07:00
obj-$(CONFIG_REGULATOR_WM831X) += wm831x-ldo.o
regulator: Add WM8350 regulator support The WM8350 features six DCDC convertors (four buck and two boost), four LDO voltage regulators and two constant current sinks. This driver adds support for these through the regulator API. This driver was written by Liam Girdwood with updates for submission from Mark Brown. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2008-10-10 07:58:15 -07:00
obj-$(CONFIG_REGULATOR_WM8350) += wm8350-regulator.o
regulator: Add WM8400 regulator support The WM8400 provides two programmable DCDC step-down (buck) convertors and four low-dropout (LDO) regulators. This driver provides support for runtime managment of these in the standard regulator API. Support for configuration of the suspend and hibernate mode behaviour of the regulators is not yet included. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2008-09-11 03:12:01 -07:00
obj-$(CONFIG_REGULATOR_WM8400) += wm8400-regulator.o
da903x: add regulator support for DA9030/DA9034 Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Liam Girdwood <lrg@kernel.org>
2008-08-26 13:16:08 -07:00
obj-$(CONFIG_REGULATOR_DA903X) += da903x.o
regulator: PCF50633 pmic driver Changes from V1: - Removed support for suspend_enable & suspend_disable functions. Signed-off-by: Balaji Rao <balajirrao@openmoko.org> Cc: Andy Green <andy@openmoko.com> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
2009-01-08 17:51:01 -07:00
obj-$(CONFIG_REGULATOR_PCF50633) += pcf50633-regulator.o
regulator: add pcap driver Add (partial) support for the voltage regulators on the PCAP2 PMIC. Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-06-26 20:18:02 -07:00
obj-$(CONFIG_REGULATOR_PCAP) += pcap-regulator.o
regulator: Add Freescale MC13783 driver This driver provides basic support for the voltage regulators integrated into the Freescale MC13783 PMIC. It is currently only possible to enable/disable outputs, not to actually set the voltage. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-08-18 16:43:50 -07:00
obj-$(CONFIG_REGULATOR_MC13783) += mc13783.o
regulator: AB3100 support This adds support for the regulators found in the AB3100 Mixed-Signal IC. It further also defines platform data for the ST-Ericsson U300 platform and extends the AB3100 MFD driver so that platform/board data with regulation constraints and an init function can be passed down all the way from the board to the regulators. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-09-09 02:31:00 -07:00
obj-$(CONFIG_REGULATOR_AB3100) += ab3100.o
regulator: TI bq24022 Li-Ion Charger driver This adds a regulator driver for the TI bq24022 Single-Chip Li-Ion Charger with its nCE and ISET2 pins connected to GPIOs. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
2008-07-11 08:28:06 -07:00
regulator: core kbuild files This patch adds kernel build support for the regulator core. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
2008-04-30 09:13:42 -07:00
ccflags-$(CONFIG_REGULATOR_DEBUG) += -DDEBUG
Copy Permalink