kevin/linux
1
Fork 0
Code
32a7991b6a
linux/drivers/bcma/driver_pci.c

278 lines
7.5 KiB
C
Raw Normal View History

bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
/*
* Broadcom specific AMBA
* PCI Core
*
bcma: add PCIe host controller Some SoCs have a PCIe host controller to make it possible to attach some other devices to it, like an other Wifi card. This code was tested with an Netgear WNDR3400 (bcm4716 based), but should work with all bcma based SoCs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:35 -07:00
* Copyright 2005, 2011, Broadcom Corporation
Update my e-mail address Signed-off-by: Michael Buesch <m@bues.ch> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-07-04 11:50:05 -07:00
* Copyright 2006, 2007, Michael Buesch <m@bues.ch>
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
* Copyright 2011, 2012, Hauke Mehrtens <hauke@hauke-m.de>
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
*
* Licensed under the GNU/GPL. See COPYING for details.
*/
#include "bcma_private.h"
bcma: fix implicit use of export.h contents Fix in advance, or we will get things like this: drivers/bcma/core.c:20: warning: data definition has no type or storage class drivers/bcma/core.c:20: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' drivers/bcma/core.c:20: warning: parameter names (without types) in function declaration Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-07-27 18:21:04 -07:00
#include <linux/export.h>
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
#include <linux/bcma/bcma.h>
/**************************************************
* R/W ops.
**************************************************/
bcma: export bcma_pcie_read() This will be needed by the host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:33 -07:00
u32 bcma_pcie_read(struct bcma_drv_pci *pc, u32 address)
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
{
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
pcicore_write32(pc, BCMA_CORE_PCI_PCIEIND_ADDR, address);
pcicore_read32(pc, BCMA_CORE_PCI_PCIEIND_ADDR);
return pcicore_read32(pc, BCMA_CORE_PCI_PCIEIND_DATA);
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
}
static void bcma_pcie_write(struct bcma_drv_pci *pc, u32 address, u32 data)
{
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
pcicore_write32(pc, BCMA_CORE_PCI_PCIEIND_ADDR, address);
pcicore_read32(pc, BCMA_CORE_PCI_PCIEIND_ADDR);
pcicore_write32(pc, BCMA_CORE_PCI_PCIEIND_DATA, data);
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
}
static void bcma_pcie_mdio_set_phy(struct bcma_drv_pci *pc, u8 phy)
{
u32 v;
int i;
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
v = BCMA_CORE_PCI_MDIODATA_START;
v |= BCMA_CORE_PCI_MDIODATA_WRITE;
v |= (BCMA_CORE_PCI_MDIODATA_DEV_ADDR <<
BCMA_CORE_PCI_MDIODATA_DEVADDR_SHF);
v |= (BCMA_CORE_PCI_MDIODATA_BLK_ADDR <<
BCMA_CORE_PCI_MDIODATA_REGADDR_SHF);
v |= BCMA_CORE_PCI_MDIODATA_TA;
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
v |= (phy << 4);
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
pcicore_write32(pc, BCMA_CORE_PCI_MDIO_DATA, v);
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
udelay(10);
for (i = 0; i < 200; i++) {
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
v = pcicore_read32(pc, BCMA_CORE_PCI_MDIO_CONTROL);
if (v & BCMA_CORE_PCI_MDIOCTL_ACCESS_DONE)
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
break;
msleep(1);
}
}
static u16 bcma_pcie_mdio_read(struct bcma_drv_pci *pc, u8 device, u8 address)
{
int max_retries = 10;
u16 ret = 0;
u32 v;
int i;
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
/* enable mdio access to SERDES */
v = BCMA_CORE_PCI_MDIOCTL_PREAM_EN;
v |= BCMA_CORE_PCI_MDIOCTL_DIVISOR_VAL;
pcicore_write32(pc, BCMA_CORE_PCI_MDIO_CONTROL, v);
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
if (pc->core->id.rev >= 10) {
max_retries = 200;
bcma_pcie_mdio_set_phy(pc, device);
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
v = (BCMA_CORE_PCI_MDIODATA_DEV_ADDR <<
BCMA_CORE_PCI_MDIODATA_DEVADDR_SHF);
v |= (address << BCMA_CORE_PCI_MDIODATA_REGADDR_SHF);
} else {
v = (device << BCMA_CORE_PCI_MDIODATA_DEVADDR_SHF_OLD);
v |= (address << BCMA_CORE_PCI_MDIODATA_REGADDR_SHF_OLD);
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
}
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
v = BCMA_CORE_PCI_MDIODATA_START;
v |= BCMA_CORE_PCI_MDIODATA_READ;
v |= BCMA_CORE_PCI_MDIODATA_TA;
pcicore_write32(pc, BCMA_CORE_PCI_MDIO_DATA, v);
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
/* Wait for the device to complete the transaction */
udelay(10);
bcma: pci: trivial: correct amount of maximum retries Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-11 15:01:47 -07:00
for (i = 0; i < max_retries; i++) {
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
v = pcicore_read32(pc, BCMA_CORE_PCI_MDIO_CONTROL);
if (v & BCMA_CORE_PCI_MDIOCTL_ACCESS_DONE) {
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
udelay(10);
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
ret = pcicore_read32(pc, BCMA_CORE_PCI_MDIO_DATA);
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
break;
}
msleep(1);
}
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
pcicore_write32(pc, BCMA_CORE_PCI_MDIO_CONTROL, 0);
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
return ret;
}
static void bcma_pcie_mdio_write(struct bcma_drv_pci *pc, u8 device,
u8 address, u16 data)
{
int max_retries = 10;
u32 v;
int i;
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
/* enable mdio access to SERDES */
v = BCMA_CORE_PCI_MDIOCTL_PREAM_EN;
v |= BCMA_CORE_PCI_MDIOCTL_DIVISOR_VAL;
pcicore_write32(pc, BCMA_CORE_PCI_MDIO_CONTROL, v);
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
if (pc->core->id.rev >= 10) {
max_retries = 200;
bcma_pcie_mdio_set_phy(pc, device);
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
v = (BCMA_CORE_PCI_MDIODATA_DEV_ADDR <<
BCMA_CORE_PCI_MDIODATA_DEVADDR_SHF);
v |= (address << BCMA_CORE_PCI_MDIODATA_REGADDR_SHF);
} else {
v = (device << BCMA_CORE_PCI_MDIODATA_DEVADDR_SHF_OLD);
v |= (address << BCMA_CORE_PCI_MDIODATA_REGADDR_SHF_OLD);
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
}
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
v = BCMA_CORE_PCI_MDIODATA_START;
v |= BCMA_CORE_PCI_MDIODATA_WRITE;
v |= BCMA_CORE_PCI_MDIODATA_TA;
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
v |= data;
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
pcicore_write32(pc, BCMA_CORE_PCI_MDIO_DATA, v);
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
/* Wait for the device to complete the transaction */
udelay(10);
for (i = 0; i < max_retries; i++) {
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
v = pcicore_read32(pc, BCMA_CORE_PCI_MDIO_CONTROL);
if (v & BCMA_CORE_PCI_MDIOCTL_ACCESS_DONE)
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
break;
msleep(1);
}
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
pcicore_write32(pc, BCMA_CORE_PCI_MDIO_CONTROL, 0);
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
}
/**************************************************
* Workarounds.
**************************************************/
static u8 bcma_pcicore_polarity_workaround(struct bcma_drv_pci *pc)
{
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
u32 tmp;
tmp = bcma_pcie_read(pc, BCMA_CORE_PCI_PLP_STATUSREG);
if (tmp & BCMA_CORE_PCI_PLP_POLARITYINV_STAT)
return BCMA_CORE_PCI_SERDES_RX_CTRL_FORCE |
BCMA_CORE_PCI_SERDES_RX_CTRL_POLARITY;
else
return BCMA_CORE_PCI_SERDES_RX_CTRL_FORCE;
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
}
static void bcma_pcicore_serdes_workaround(struct bcma_drv_pci *pc)
{
u16 tmp;
bcma: add constants for PCI and use them There are many magic numbers used in the PCIe code. Replace them with some constants from the Broadcom SDK and also use them in the pcie host controller. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:32 -07:00
bcma_pcie_mdio_write(pc, BCMA_CORE_PCI_MDIODATA_DEV_RX,
BCMA_CORE_PCI_SERDES_RX_CTRL,
bcma_pcicore_polarity_workaround(pc));
tmp = bcma_pcie_mdio_read(pc, BCMA_CORE_PCI_MDIODATA_DEV_PLL,
BCMA_CORE_PCI_SERDES_PLL_CTRL);
if (tmp & BCMA_CORE_PCI_PLL_CTRL_FREQDET_EN)
bcma_pcie_mdio_write(pc, BCMA_CORE_PCI_MDIODATA_DEV_PLL,
BCMA_CORE_PCI_SERDES_PLL_CTRL,
tmp & ~BCMA_CORE_PCI_PLL_CTRL_FREQDET_EN);
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
}
bcma: add bcma_core_pci_fixcfg() This code is based on code from pcicore_fixcfg() in brcmsmac. This patch is part of the move of pci specific code from brcmsmac to bcma. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Tested-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-28 17:18:51 -07:00
static void bcma_core_pci_fixcfg(struct bcma_drv_pci *pc)
{
struct bcma_device *core = pc->core;
u16 val16, core_index;
uint regoff;
regoff = BCMA_CORE_PCI_SPROM(BCMA_CORE_PCI_SPROM_PI_OFFSET);
core_index = (u16)core->core_index;
val16 = pcicore_read16(pc, regoff);
if (((val16 & BCMA_CORE_PCI_SPROM_PI_MASK) >> BCMA_CORE_PCI_SPROM_PI_SHIFT)
!= core_index) {
val16 = (core_index << BCMA_CORE_PCI_SPROM_PI_SHIFT) |
(val16 & ~BCMA_CORE_PCI_SPROM_PI_MASK);
pcicore_write16(pc, regoff, val16);
}
}
bcma: add bcma_core_pci_config_fixup() This code is based on code from pcie_misc_config_fixup() in brcmsmac. This patch is part of the move of pci specific code from brcmsmac to bcma. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Tested-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-28 17:18:52 -07:00
/* Fix MISC config to allow coming out of L2/L3-Ready state w/o PRST */
/* Needs to happen when coming out of 'standby'/'hibernate' */
static void bcma_core_pci_config_fixup(struct bcma_drv_pci *pc)
{
u16 val16;
uint regoff;
regoff = BCMA_CORE_PCI_SPROM(BCMA_CORE_PCI_SPROM_MISC_CONFIG);
val16 = pcicore_read16(pc, regoff);
if (!(val16 & BCMA_CORE_PCI_SPROM_L23READY_EXIT_NOPERST)) {
val16 |= BCMA_CORE_PCI_SPROM_L23READY_EXIT_NOPERST;
pcicore_write16(pc, regoff, val16);
}
}
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
/**************************************************
* Init.
**************************************************/
bcma: make some functions __devinit bcma_core_pci_hostmode_init() has to be in __devinit as it will call a function in that section and so all functions calling it also have to be in __devinit. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:34 -07:00
static void __devinit bcma_core_pci_clientmode_init(struct bcma_drv_pci *pc)
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
{
bcma: add bcma_core_pci_fixcfg() This code is based on code from pcicore_fixcfg() in brcmsmac. This patch is part of the move of pci specific code from brcmsmac to bcma. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Tested-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-28 17:18:51 -07:00
bcma_core_pci_fixcfg(pc);
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
bcma_pcicore_serdes_workaround(pc);
bcma: add bcma_core_pci_config_fixup() This code is based on code from pcie_misc_config_fixup() in brcmsmac. This patch is part of the move of pci specific code from brcmsmac to bcma. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Tested-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-28 17:18:52 -07:00
bcma_core_pci_config_fixup(pc);
bcma: add Broadcom specific AMBA bus driver Broadcom has released cards based on a new AMBA-based bus type. From a programming point of view, this new bus type differs from AMBA and does not use AMBA common registers. It also differs enough from SSB. We decided that a new bus driver is needed to keep the code clean. In its current form, the driver detects devices present on the bus and registers them in the system. It allows registering BCMA drivers for specified bus devices and provides them basic operations. The bus driver itself includes two important bus managing drivers: ChipCommon core driver and PCI(c) core driver. They are early used to allow correct initialization. Currently code is limited to supporting buses on PCI(e) devices, however the driver is designed to be used also on other hosts. The host abstraction layer is implemented and already used for PCI(e). Support for PCI(e) hosts is working and seems to be stable (access to 80211 core was tested successfully on a few devices). We can still optimize it by using some fixed windows, but this can be done later without affecting any external code. Windows are just ranges in MMIO used for accessing cores on the bus. Cc: Greg KH <greg@kroah.com> Cc: Michael Büsch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: George Kashperko <george@znau.edu.ua> Cc: Arend van Spriel <arend@broadcom.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Botting <andy@andybotting.com> Cc: linuxdriverproject <devel@linuxdriverproject.org> Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-09 09:56:46 -07:00
}
bcma: pci: implement interrupts control Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-19 05:08:22 -07:00
bcma: make some functions __devinit bcma_core_pci_hostmode_init() has to be in __devinit as it will call a function in that section and so all functions calling it also have to be in __devinit. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:34 -07:00
void __devinit bcma_core_pci_init(struct bcma_drv_pci *pc)
bcma: detect PCI core working in hostmode We must not init it like clientmode one, it would break device (tested by Hauke on BCM4718). Add stub hostmode driver for now. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-05 10:48:26 -07:00
{
bcma: add functions to scan cores needed on SoCs The chip common and mips core have to be setup early in the boot process to get the cpu clock. bcma_bus_early_register() gets pointers to some space to store the core data and searches for the chip common and mips core and initializes chip common. After that was done and the kernel is out of early boot we just have to run bcma_bus_register() and it will search for the other cores, initialize and register them. The cores are getting the same numbers as before. Acked-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-22 16:20:07 -07:00
if (pc->setup_done)
return;
bcma: detect PCI core working in hostmode We must not init it like clientmode one, it would break device (tested by Hauke on BCM4718). Add stub hostmode driver for now. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-05 10:48:26 -07:00
#ifdef CONFIG_BCMA_DRIVER_PCI_HOSTMODE
bcma: add PCIe host controller Some SoCs have a PCIe host controller to make it possible to attach some other devices to it, like an other Wifi card. This code was tested with an Netgear WNDR3400 (bcm4716 based), but should work with all bcma based SoCs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:35 -07:00
pc->hostmode = bcma_core_pci_is_in_hostmode(pc);
if (pc->hostmode)
bcma: detect PCI core working in hostmode We must not init it like clientmode one, it would break device (tested by Hauke on BCM4718). Add stub hostmode driver for now. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-05 10:48:26 -07:00
bcma_core_pci_hostmode_init(pc);
#endif /* CONFIG_BCMA_DRIVER_PCI_HOSTMODE */
bcma: add functions to scan cores needed on SoCs The chip common and mips core have to be setup early in the boot process to get the cpu clock. bcma_bus_early_register() gets pointers to some space to store the core data and searches for the chip common and mips core and initializes chip common. After that was done and the kernel is out of early boot we just have to run bcma_bus_register() and it will search for the other cores, initialize and register them. The cores are getting the same numbers as before. Acked-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-22 16:20:07 -07:00
bcma: add PCIe host controller Some SoCs have a PCIe host controller to make it possible to attach some other devices to it, like an other Wifi card. This code was tested with an Netgear WNDR3400 (bcm4716 based), but should work with all bcma based SoCs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30 16:03:35 -07:00
if (!pc->hostmode)
bcma_core_pci_clientmode_init(pc);
bcma: detect PCI core working in hostmode We must not init it like clientmode one, it would break device (tested by Hauke on BCM4718). Add stub hostmode driver for now. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-05 10:48:26 -07:00
}
bcma: pci: implement interrupts control Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-19 05:08:22 -07:00
int bcma_core_pci_irq_ctl(struct bcma_drv_pci *pc, struct bcma_device *core,
bool enable)
{
bcma: fix null pointer in bcma_core_pci_irq_ctl pc could be null if hosttype != BCMA_HOSTTYPE_PCI. If we are on a device without a pci core this function is called with pc = null by b43 and brcmsmac. If the host type is PCI we have a pci core as well and pc can not be null. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-05 11:58:20 -07:00
struct pci_dev *pdev;
bcma: pci: implement interrupts control Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-19 05:08:22 -07:00
u32 coremask, tmp;
bcma: add SOC bus This patch adds support for using bcma on a Broadcom SoC as the system bus. An SoC like the bcm4716 could register this bus and use it to searches for the bcma cores and register the devices on this bus. BCMA_HOSTTYPE_NONE was intended for SoCs at first but BCMA_HOSTTYPE_SOC is a better name. Acked-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-22 16:20:08 -07:00
int err = 0;
bcma: fix null pointer in bcma_core_pci_irq_ctl pc could be null if hosttype != BCMA_HOSTTYPE_PCI. If we are on a device without a pci core this function is called with pc = null by b43 and brcmsmac. If the host type is PCI we have a pci core as well and pc can not be null. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-05 11:58:20 -07:00
if (!pc || core->bus->hosttype != BCMA_HOSTTYPE_PCI) {
bcma: add SOC bus This patch adds support for using bcma on a Broadcom SoC as the system bus. An SoC like the bcm4716 could register this bus and use it to searches for the bcma cores and register the devices on this bus. BCMA_HOSTTYPE_NONE was intended for SoCs at first but BCMA_HOSTTYPE_SOC is a better name. Acked-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-22 16:20:08 -07:00
/* This bcma device is not on a PCI host-bus. So the IRQs are
* not routed through the PCI core.
* So we must not enable routing through the PCI core. */
goto out;
}
bcma: pci: implement interrupts control Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-19 05:08:22 -07:00
bcma: fix null pointer in bcma_core_pci_irq_ctl pc could be null if hosttype != BCMA_HOSTTYPE_PCI. If we are on a device without a pci core this function is called with pc = null by b43 and brcmsmac. If the host type is PCI we have a pci core as well and pc can not be null. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-05 11:58:20 -07:00
pdev = pc->core->bus->host_pci;
bcma: pci: implement interrupts control Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-19 05:08:22 -07:00
err = pci_read_config_dword(pdev, BCMA_PCI_IRQMASK, &tmp);
if (err)
goto out;
coremask = BIT(core->core_index) << 8;
if (enable)
tmp |= coremask;
else
tmp &= ~coremask;
err = pci_write_config_dword(pdev, BCMA_PCI_IRQMASK, tmp);
out:
return err;
}
bcma: clean exports of functions Function managing IRQs is needed for external drivers like b43. On the other side we do not expect writing any hosts drivers outside of bcma, so this is safe to do not export functions related to this. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-17 16:01:59 -07:00
EXPORT_SYMBOL_GPL(bcma_core_pci_irq_ctl);
bcma: add bcma_core_pci_extend_L1timer This code is based on code from pcie_extendL1timer() in brcmsmac. This patch is part of the move of pci specific code from brcmsmac to bcma. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Tested-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-28 17:18:50 -07:00
void bcma_core_pci_extend_L1timer(struct bcma_drv_pci *pc, bool extend)
{
u32 w;
w = bcma_pcie_read(pc, BCMA_CORE_PCI_DLLP_PMTHRESHREG);
if (extend)
w |= BCMA_CORE_PCI_ASPMTIMER_EXTEND;
else
w &= ~BCMA_CORE_PCI_ASPMTIMER_EXTEND;
bcma_pcie_write(pc, BCMA_CORE_PCI_DLLP_PMTHRESHREG, w);
bcma_pcie_read(pc, BCMA_CORE_PCI_DLLP_PMTHRESHREG);
}
EXPORT_SYMBOL_GPL(bcma_core_pci_extend_L1timer);
Copy Permalink