2019-09-02 06:08:28 -07:00
|
|
|
What: /sys/bus/iio/devices/iio:deviceX/ac_excitation_en
|
|
|
|
|
KernelVersion:
|
|
|
|
|
Contact: linux-iio@vger.kernel.org
|
|
|
|
|
Description:
|
2020-02-12 09:17:20 -07:00
|
|
|
This attribute, if available, is used to enable the AC
|
|
|
|
|
excitation mode found on some converters. In ac excitation mode,
|
|
|
|
|
the polarity of the excitation voltage is reversed on
|
|
|
|
|
alternate cycles, to eliminate DC errors.
|
2019-09-02 06:08:28 -07:00
|
|
|
|
|
|
|
|
What: /sys/bus/iio/devices/iio:deviceX/bridge_switch_en
|
|
|
|
|
KernelVersion:
|
|
|
|
|
Contact: linux-iio@vger.kernel.org
|
|
|
|
|
Description:
|
2020-02-12 09:17:20 -07:00
|
|
|
This attribute, if available, is used to close or open the
|
|
|
|
|
bridge power down switch found on some converters.
|
|
|
|
|
In bridge applications, such as strain gauges and load cells,
|
|
|
|
|
the bridge itself consumes the majority of the current in the
|
|
|
|
|
system. To minimize the current consumption of the system,
|
|
|
|
|
the bridge can be disconnected (when it is not being used
|
|
|
|
|
using the bridge_switch_en attribute.
|
2019-09-02 06:08:30 -07:00
|
|
|
|
|
|
|
|
What: /sys/bus/iio/devices/iio:deviceX/in_voltagex_sys_calibration
|
|
|
|
|
KernelVersion:
|
|
|
|
|
Contact: linux-iio@vger.kernel.org
|
|
|
|
|
Description:
|
|
|
|
|
Initiates the system calibration procedure. This is done on a
|
|
|
|
|
single channel at a time. Write '1' to start the calibration.
|
|
|
|
|
|
2020-02-12 09:17:20 -07:00
|
|
|
What: /sys/bus/iio/devices/iio:deviceX/in_voltage2-voltage2_shorted_raw
|
|
|
|
|
KernelVersion:
|
|
|
|
|
Contact: linux-iio@vger.kernel.org
|
|
|
|
|
Description:
|
|
|
|
|
Measure voltage from AIN2 pin connected to AIN(+)
|
|
|
|
|
and AIN(-) shorted.
|
|
|
|
|
|
2019-09-02 06:08:30 -07:00
|
|
|
What: /sys/bus/iio/devices/iio:deviceX/in_voltagex_sys_calibration_mode_available
|
|
|
|
|
KernelVersion:
|
|
|
|
|
Contact: linux-iio@vger.kernel.org
|
|
|
|
|
Description:
|
|
|
|
|
Reading returns a list with the possible calibration modes.
|
|
|
|
|
There are two available options:
|
|
|
|
|
"zero_scale" - calibrate to zero scale
|
|
|
|
|
"full_scale" - calibrate to full scale
|
|
|
|
|
|
|
|
|
|
What: /sys/bus/iio/devices/iio:deviceX/in_voltagex_sys_calibration_mode
|
|
|
|
|
KernelVersion:
|
|
|
|
|
Contact: linux-iio@vger.kernel.org
|
|
|
|
|
Description:
|
|
|
|
|
Sets up the calibration mode used in the system calibration
|
|
|
|
|
procedure. Reading returns the current calibration mode.
|
|
|
|
|
Writing sets the system calibration mode.
|
