mirror of
https://github.com/Koenkk/zigbee2mqtt.git
synced 2024-11-17 10:58:31 -07:00
46 lines
3.0 KiB
Markdown
46 lines
3.0 KiB
Markdown
|
# Flashing the firmware on the CC2531 USB stick
|
||
|
|
The CC2531 USB stick needs to be flashed with a custom firmware.
|
||
|
|
|
||
|
|
*NOTE: The following instructions assume you have a CC Debugger. In case you don't, see [Alternative firmware flashing methods](../useful_information/alternative-firmware-flashing-methods.md).*
|
||
|
|
|
||
|
|
## Windows
|
||
|
|
1. Install [SmartRF Flash programmer](http://www.ti.com/tool/FLASH-PROGRAMMER) (**NOT V2**). This software is free but requires a Texas Instruments account in order to download.
|
||
|
|
2. Install the [CC debugger driver](http://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=swrc212&fileType=zip) on your PC (Windows only). Before continuing, verify that the CC Debugger driver has been installed correctly. See [Figure 1. Verify Correct Driver Installation @ Chapter 5.1](http://www.ti.com/lit/ug/swru197h/swru197h.pdf). In case the CC Debugger is not recognized correctly [install the driver manually](https://www.youtube.com/watch?v=jyKrxxXOvQY).
|
||
|
|
2. Connect `CC debugger --> Downloader cable CC2531 --> CC2531 USB sniffer`.
|
||
|
|
3. Connect **BOTH** the `CC2531 USB sniffer` and the `CC debugger` to your PC using USB.
|
||
|
|
3. If the light on the CC debugger is RED press set reset button on the CC debugger. The light on the CC debugger should now turn GREEN. If not use [CC debugger user guide](http://www.ti.com/lit/ug/swru197h/swru197h.pdf) to troubleshoot your problem.
|
||
|
|
|
||
|
|
|
||
|
|
4. Download the firmware [CC2531ZNP-Prod.hex](https://raw.githubusercontent.com/Koenkk/Z-Stack-firmware/master/coordinator/CC2531/bin/CC2531ZNP-Prod.hex)
|
||
|
|
5. Start SmartRF Flash Programmer, setup as shown below and press `Perform actions`.
|
||
|
|
|
||
|
|
|
||
|
|
## Linux or MacOS
|
||
|
|
Credits to [@Frans-Willem](https://github.com/frans-Willem) for majority of instructions.
|
||
|
|
|
||
|
|
1. Install prerequisites for [CC-Tool](https://github.com/dashesy/cc-tool) using a package manager (e.g. [Homebrew](https://brew.sh/) for macOS)
|
||
|
|
> Ubuntu: dh-autoreconf, libusb-1.0, libboost-all-dev
|
||
|
|
> Fedora: dh-autoreconf, boost-devel, libusb1-devel
|
||
|
|
> Archlinux: dh-autoreconf, libusb, boost
|
||
|
|
> macOS: autoconf, automake, libusb, boost, pkgconfig, libtool
|
||
|
|
|
||
|
|
2. Build cc-tool
|
||
|
|
```bash
|
||
|
|
git clone https://github.com/dashesy/cc-tool.git
|
||
|
|
cd cc-tool
|
||
|
|
./bootstrap
|
||
|
|
./configure
|
||
|
|
make
|
||
|
|
```
|
||
|
|
3. Connect `CC debugger --> Downloader cable CC2531 --> CC2531 USB sniffer`.
|
||
|
|
4. Connect **BOTH** the `CC2531 USB sniffer` and the `CC debugger` to your PC using USB.
|
||
|
|
5. If the light on the CC debugger is RED, press the Reset button on the CC debugger. The light on the CC debugger should now turn GREEN. If not, follow the [CC debugger user guide](http://www.ti.com/lit/ug/swru197h/swru197h.pdf) to troubleshoot your problem.
|
||
|
|
|
||
|
|
6. Download the firmware [CC2531ZNP-Prod.hex](https://raw.githubusercontent.com/Koenkk/Z-Stack-firmware/master/coordinator/CC2531/bin/CC2531ZNP-Prod.hex).
|
||
|
|
7. Flash your firmware:
|
||
|
|
```
|
||
|
|
sudo ./cc-tool -e -w CC2531ZNP-Prod.hex
|
||
|
|
```
|
||
|
|
|
||
|
|
# What's next?
|
||
|
|
[Running Zigbee2mqtt](running_zigbee2mqtt.md)
|